A standard roll-in shower must be at least 30 inches wide by 60 inches deep inside, and an alternate roll-in must be at least 36 inches wide by 60 inches deep. Those figures come from the federal accessibility standards. The rest of the design, from the threshold to the slope of the floor to where the controls go, follows from them. Below we walk through each requirement, explain which ones legally apply to a private home in Albuquerque, and show how to plan a roll-in shower you will actually be comfortable using.
TL;DR
- A standard roll-in compartment is 30 inches wide by 60 inches deep at minimum. An alternate roll-in is 36 inches wide by 60 inches deep at minimum, measured clear inside.
- Thresholds may be up to 1/2 inch high if beveled, but a flush, curbless entry is easier to roll across. Floors can slope to the drain at no more than 1:48.
- Controls must sit no higher than 48 inches above the shower floor and above the grab bars. A seat, if you include one, must fold up and mount to the wall.
- ADA design standards are not enforced by city permit offices for a single-family home, but they are the best published benchmark for a bathroom that works for a wheelchair user.
Table of Contents
- What a roll-in shower is
- Do ADA requirements apply to your home?
- Minimum roll-in shower dimensions
- Entry, thresholds and floor slope
- Controls, seat and grab bars
- A quick planning checklist
- How a roll-in project usually unfolds
- Our perspective
- Plan your roll-in shower with us
- FAQ
- Sources
What a roll-in shower is
A roll-in shower lets someone enter on a shower chair or other wheeled mobility aid without transferring to a seat. The U.S. Access Board describes it in its guidance on bathing rooms as a compartment designed to give access for shower chairs and other wheeled aids. There is no tub wall to lift over, and no step to manage.
People search for this under several names: wheelchair accessible shower, barrier free shower, curbless shower, zero-threshold shower. They overlap but are not identical. A curbless shower is defined by its entry. A roll-in shower is defined by its size, its clear floor space and its fixtures. You can build a curbless shower that is too small for a wheelchair, and you can build a roll-in with a small beveled threshold. The best accessible showers are both.
Do ADA requirements apply to your home?
This is the question that decides how strict you need to be, so it comes first.
The ADA design standards apply to public accommodations, commercial facilities and state and local government buildings. A single-family home is generally not covered. A City of San Diego guide on curbless showers notes that single-family bathrooms generally need not meet state accessibility codes or ADA design requirements, with few exceptions, while curbless showers in multifamily buildings that must provide accessible units do have to comply. That guide on curbless showers is from 2003 and from California, so treat it as background on the principle rather than a statement of New Mexico law.
The Access Board also explains that the ADA is a civil rights law and not a building code. In its guide to using the ADA Standards, it says covered entities are responsible for their own compliance and that building departments are not authorized or required to enforce ADA design standards during plan review.
What that means for you as a homeowner:
- Nobody will fail your home shower for being 34 inches wide instead of 36.
- The ADA dimensions are still the most widely tested numbers for a shower a wheelchair user can enter and turn in.
- If you ever rent a unit, add a unit to a multifamily property or run a business out of the building, the standards may apply, so building to them from the start avoids rework.
Permits are a separate matter. Moving a shower drain or supply lines is plumbing work, and that is a question for the city, not the ADA. Our guide to bathroom permits in Albuquerque covers what to check before work starts.
Minimum roll-in shower dimensions
The ADA Standards recognize two roll-in compartments. The numbers below come from section 608 as reproduced in the Architectural Barriers Act guide.
| Type | Minimum clear width | Minimum clear depth | Entry |
|---|---|---|---|
| Standard roll-in | 30 inches | 60 inches | Short end of the compartment, opposite the back wall |
| Alternate roll-in | 36 inches | 60 inches | Open along one long side, at least 36 inches wide |
The clear inside dimensions are measured at the center points of opposing sides. That detail matters in practice. A 60 inch rough opening drops below 60 inches clear once tile, a membrane and a wall panel are added. When we plan a roll-in, we work from the finished, clear measurement, not the framing.
Standard versus alternate
A standard roll-in is compact and works where bathroom space is tight. It is entered from the end, so the person rolling in has to line up with a 30 inch opening and then move through a 30 inch wide space. That is workable with a manual chair and a careful approach, but it leaves little room to turn.
The alternate roll-in is wider and open along the side, which makes approach much easier, particularly for a caregiver who needs room to stand beside the chair. If your bathroom can spare the extra 6 inches of width, we usually point homeowners toward the alternate layout.
What about going bigger?
The minimums are minimums. Many households choose a larger shower, because a power chair, a caregiver or a long-term plan for a shower chair all need more room than a bare-minimum compartment gives. Because the standards set floors and not ceilings, the right size is the largest one your bathroom layout can support without compromising the rest of the room. If you are weighing whether you can fit that in, our aging in place bathroom guide covers how to look at the whole room, including door width and turning space.
Entry, thresholds and floor slope
The entry is the feature that makes a roll-in a roll-in.
According to the Access Board’s bathing room guidance:
- A roll-in threshold may be up to 1/2 inch high if properly beveled.
- Any threshold higher than 1/4 inch must be beveled at a maximum slope of 1:2.
- A flush transition gives easier access than a beveled lip.
- Shower floors may slope toward drains at a maximum of 1:48.
A 1:48 slope is about a quarter inch of drop per foot. It is gentle enough that a chair will not drift, and enough for water to find the drain. If you want a floor that feels flat, this limit is the ceiling for how much you can pitch it.
Managing water in a curbless shower
Remove the curb and you lose the simplest barrier that kept water in the shower. The San Diego guide identifies water containment as the key design challenge in curbless showers, and says that drain and floor-slope details are how you manage it. In practice that means a few decisions made before the first tile goes down:
- Recess the floor. A curbless entry usually needs the shower floor set lower than the bathroom floor, which means modifying the subfloor or framing. That is why a curbless conversion is a structural conversation and not only a tile job.
- Plan the drain. A linear drain along the entry or back wall lets you slope the floor in one direction, while a center drain slopes the floor from four sides. Each affects how the tile is cut and how comfortable the surface is to roll across.
- Slope toward the drain, not just any direction. Keep within the 1:48 limit so the floor still works for a chair.
- Think about splash. A longer shower area, a glass panel and a handheld shower with a controllable spray all reduce water reaching the rest of the bathroom.
- Waterproof the whole assembly. A roll-in shower sees constant water, and the joints are where failures start. Keeping up with caulk versus grout in showers helps you understand which joints should flex and which should be rigid. If you are tackling a tile shower yourself, our guide to tile shower waterproofing walks through the layers.
What is a roll-in shower pan?
A shower pan is the sloped floor of the compartment, the surface that collects water and delivers it to the drain. For a roll-in, that can be a prefabricated base with a very low or beveled edge, or a custom-built, tiled floor over a waterproof membrane. Prefabricated bases are quick to install and come in standard sizes, so check that the advertised size matches the clear inside dimensions above, not just the outer footprint. A custom tiled pan can be built to any dimension and can run flush into the bathroom floor, which is why it is the usual choice for a truly barrier-free entry. The trade-off for a custom pan is that it demands careful framing, slope and waterproofing, so it is best handled by an experienced remodeler.
Controls, seat and grab bars
The fixtures are where a shower that technically fits a wheelchair becomes one a person can actually use.
Controls and spray unit
The Access Board states that controls, faucets and shower spray units must be above the grab bars and at least 1 1/2 inches above the gripping surface, and no higher than 48 inches above the shower floor. Reaching a valve is easier when you do not have to lean through spray to do it, so we usually set the controls on the wall near the entry side of the seat location, where someone can turn the water on before moving into it.
In a standard roll-in with a seat, the section 608 guide says the controls must be on the back wall, adjacent to the seat wall and no more than 27 inches from the seat wall. A handheld spray unit on a slide bar is a very practical addition because it can be used seated, standing or by a caregiver.
Seat
If you include a seat, the Access Board says it must fold up and attach to the wall. A folding seat leaves the floor clear when someone rolls in on their own chair, and gives a place to sit for people who can transfer. Some households skip a built-in seat and use a portable shower chair instead. Both approaches work. The folding wall seat just needs strong backing in the wall.
Grab bars
Grab bars go on the back wall and on the side wall opposite the seat. The bars themselves do the job only if the wall behind them can carry a person’s full weight. Install solid blocking between the studs while the walls are open, even if you do not plan to mount bars yet. It costs little during construction and avoids opening finished tile later.
The ADA Standards also expect accessibility features to be fixed or built in unless the rules specifically permit otherwise, according to the Access Board’s guide to using the standards. In a home, that principle is a good habit: a permanently mounted bar is safer than a suction-cup version.
A quick planning checklist
Before you commit to a design, walk through these:
- Measure clear inside dimensions, after tile and wall finishes, not framing.
- Choose standard or alternate roll-in based on how much width you can spare.
- Decide on the entry: flush, or beveled at 1/2 inch or less.
- Set the floor slope at 1:48 or gentler, toward a drain placed to suit your entry.
- Position controls at 48 inches or lower above the shower floor, and above the grab bars.
- Add wall blocking for grab bars and a folding seat.
- Check the bathroom around the shower: door width, clear floor space, toilet and sink access.
- Confirm permits for any drain or plumbing moves.
How a roll-in project usually unfolds
Most homeowners who call us about a roll-in start with an existing tub or a small stall shower. The first question is whether the space can be reshaped. A tub-to-shower conversion is often the simplest route, since a tub already occupies a long, narrow footprint close to the 60 inch dimension a roll-in needs. Our guide to tub to shower conversions explains the options.
From there the sequence tends to look like this:
- Measure and assess. We check the room, the subfloor, the drain location and the framing.
- Settle the layout. Standard or alternate roll-in, seat or no seat, drain type and fixture positions.
- Handle permits. Plumbing changes go through the city.
- Demolish and frame. Recess the floor if needed and add blocking.
- Slope, waterproof and tile. The pan is formed, the membrane installed and tested, then tile set.
- Install fixtures. Controls, spray unit, seat and grab bars go in last.
Because a roll-in touches plumbing, framing, waterproofing and tile, it is a multi-trade job, and coordination matters. If you are also thinking about cost, our page on curbless shower costs in Albuquerque breaks down what drives the budget, and our bathroom remodel financing guide covers payment options.
Our perspective
Most people ask us for the dimensions first, and that is the right place to start. But the best roll-in showers we have seen are not the ones that hit the minimum numbers. They are the ones where someone thought about how the person using the shower actually lives.
We build a roll-in the way we build any bathroom: from the subfloor up. The slope, the drain and the waterproofing decide whether the shower still works in ten years, and tile only decides how it looks. That is why we prefer to handle the framing, plumbing coordination and tile under one project plan, with one team accountable for the result.
Our approach is personalized. Some households need a full alternate roll-in with a folding seat and a handheld spray. Others want a clean, curbless look with room to age in place. We offer a range of styles and budgets, and we talk through the trade-offs plainly before work begins, so you are never surprised partway through.
With over 25 years of local experience, we know how Albuquerque homes are built and what usually sits behind the wall. We would rather plan the details with you early than fix them late.
Christy Trussell
Plan your roll-in shower with us
If you are ready to turn these requirements into a layout, our team handles bathroom remodels in Albuquerque from first measurement to final tile, including accessible and curbless showers. We coordinate the trades, keep you informed throughout and offer financing options, including 0% financing.
See our bathroom remodeling services or start from our main site to talk through your project.
FAQ
What size is a wheelchair accessible shower?
According to the ADA standards, a standard roll-in shower is at least 30 inches wide by 60 inches deep, and an alternate roll-in is at least 36 inches wide by 60 inches deep. Both are measured as clear inside dimensions. A transfer-type shower is a different, smaller design for people who move from the chair to a seat, so the roll-in sizes are the ones to use if you want to stay in your chair.
Do I need a curb in a roll-in shower?
No. A roll-in shower is meant to be entered without a step. The Access Board allows a threshold of up to 1/2 inch if it is beveled, and notes that a flush transition is easier to cross. Keeping water inside without a curb depends on the floor slope, the drain placement and good waterproofing.
How high can the shower controls be?
Controls, faucets and spray units must be no higher than 48 inches above the shower floor and set above the grab bars. In a standard roll-in with a seat, controls go on the back wall next to the seat wall, no more than 27 inches from it.
Does my Albuquerque home have to meet ADA shower requirements?
Generally no for a single-family home. The ADA is enforced through complaints and litigation, not through city permit review. The standards remain a useful guide for a bathroom that truly works for a wheelchair, and plumbing changes still need the proper permits.
Recent Comments